Multiple Choice
Identify the
letter of the choice that best completes the statement or answers the question.
|
|
|
1.
|
The
bolt pictured has a strength rating of:
|
|
|
2.
|
Outside micrometers are used to measure: a. | outside
diameters | c. | thickness | b. | inside diameters | d. | both A and C | | | | |
|
|
|
3.
|
When
servicing automotive components it is often necessary to measure accurately to: a. | .001” | c. | both A and
B | b. | .01
mm | d. | none of the
above | | | | |
|
|
|
4.
|
Which
of the following tools would be the best for measuring brake rotor run-out? a. | a
micrometer | c. | a dial
indicator | b. | a feeler gauge | d. | a dial caliper | | | | |
|
|
|
5.
|
You
are measuring a piston’s diameter with a 3” to 4” micrometer. The micrometer reads
.356”. What is the actual piston diameter? a. | 4.356” | c. | 3.356” | b. | 0.356” | d. | dependent upon
piston bore size | | | | |
|
|
|
6.
|
Micrometers with a vernier scale are accurate to: a. | .0001 | c. | .00001 | b. | .01 | d. | .001 | | | | |
|
|
|
7.
|
Which
of the following tools would be the most accurate for measuring diameter? a. | vernier
caliper | c. | dial
caliper | b. | micrometer | d. | dial indicator | | | | |
|
|
|
8.
|
What
does the P in the fire extinguisher operation acronym PASS stand for? a. | press | c. | pollute | b. | pull | d. | pressure | | | | |
|
|
|
9.
|
An
MSDS contains information on: a. | proper welding procedures | c. | proper operation procedures for asbestos containment
equipment | b. | hazardous materials encountered in the work
place | d. | eye protection
equipment | | | | |
|
|
|
10.
|
Which
of the following statements is true in regard to using floor jacks? a. | check the
condition of the jack before using it | c. | both of the above | b. | always use jack
stands to support the vehicle before beginning service | d. | none of the above | | | | |
|
|
|
11.
|
Which
of the following statements is not true in regard to using vehicle lifts? a. | use the
manufacturer’s recommended lift points | c. | do not use lift locks or jack stands | b. | raise the
vehicle a few inches and check for stability | d. | inspect the lift and vehicle before
lifting | | | | |
|
|
|
12.
|
You
should wear safety glasses when: a. | drilling | c. | charging an air conditioning system | b. | grinding | d. | all of the
above | | | | |
|
|
|
13.
|
Identify the symbol shown:
a. | safety
alert | c. | owner hand book
reference | b. | fire hazard | d. | high voltage | | | | |
|
|
|
14.
|
Identify the symbol shown:
a. | fire
hazard | c. | high
voltage | b. | explosive hazard | d. | corrosive substance | | | | |
|
|
|
15.
|
The
three C’s of a properly documented repair order include: a. | car, concern,
cause | c. | concern, cause,
correction | b. | concern, complaint, cause | d. | creepy, crawly, critters | | | | |
|
|
|
16.
|
In a
large repair facility or dealership your actual work assignments most likely come
from: a. | car
salesmen | c. | service
technicians | b. | the dispatcher | d. | the shop foreman | | | | |
|
|
|
17.
|
Which
of the following wrenches would be most effective at breaking a tight bolt loose? a. | adjustable
end | c. | open
end | b. | box
end | d. | none of the
above | | | | |
|
|
|
18.
|
This
tool is used to:
a. | remove and
install brake hold down springs | c. | remove and
install brake return springs | b. | adjust rear drum brakes | d. | adjust front disc brakes | | | | |
|
|
|
19.
|
Which
of the following of torque wrenches would be the fastest to use when assembling
engines? a. | click
type | c. | beam
type | b. | dial
type | d. | none of the
above | | | | |
|
|
|
20.
|
Which
of the following of torque wrenches would be the most accurate to use when assembling
engines? a. | click
type | c. | dial
type | b. | beam
type | d. | none of the
above | | | | |
|
|
|
21.
|
The
wrench shown is:
a. | a combination
wrench | c. | an Allen
wrench | b. | an open end wrench | d. | an adjustable wrench | | | | |
|
|
|
22.
|
Which
of the following tools would be best for installing a hardened gear on a shaft? a. | rubber
mallet | c. | dead-blow
hammer | b. | ballpeen hammer | d. | sledge hammer | | | | |
|
|
|
23.
|
This
tool for use with:
a. | torque to yield
bolts | c. | standard
bolts | b. | metric bolts | d. | zero force loading bolts | | | | |
|
|
|
24.
|
Technician A says impact wrenches are used to accurately torque engine component
fasteners during assembly. Technician B says air ratchets are used to speed disassembly during
automotive service. Who is correct? a. | A only | c. | both A and B | b. | B
only | d. | neither A nor
B | | | | |
|
|
|
25.
|
The
tool shown is:
a. | a ballpeen
hammer | c. | a
mallet | b. | a dead-blow hammer | d. | none of the above | | | | |
|